Products
Mica Tape in Spool

Mica Tape in Spool

R-5461 Mica Tape in Spool is a fire-resistant cable insulation tape with phlogopite, synthetic or calcined mica paper, reinforced by alkali-free glass fibre cloth or polymer film. Thickness 0.08–0.20 mm, width 4.5–1000 mm, up to 50,000 m per spool on 52/54/76/120 mm cores. Meets BS 6387 850–900 ℃ and IEC 60331. Contact Kaxite for a free sample and quotation.

R-5461 Series · Fire-Resistant Cable Mica Tape

Mica Tape in Spool

Spooled mica tape is built on high-grade phlogopite mica paper, synthetic mica paper or calcined mica paper, reinforced on one or both sides with alkali-free glass fibre cloth or polymer film, then bonded with silicone resin and cured through high-temperature baking, drying and slitting. It is wrapped between the conductor core and the sheath of fire-resistant cables, where it holds the circuit intact when the fire reaches the cable.

A standard roll holds only 500–1,000 m, which means frequent reel changes on a high-speed wrapping line. The spool format removes that bottleneck: one tray can carry up to 50,000 m of tape, with a tray diameter of 400 mm and a height of 400 mm.

50,000 mMax length per spool
0.08–0.20 mmTape thickness
4.5–1000 mmSlitting width
850–900 ℃BS 6387 fire rating

01Spool Format: Fewer Stops, Longer Runs

Mica tape in spool wound on a 400 mm tray for fire-resistant cable wrapping lines
One tray, one continuous run. Instead of swapping a 500 m roll every few minutes, the winding line can run on a single spool for a full shift and beyond. The tape stays dry, non-adhesive and flat right to the last metre, so the wrapping tension does not drift from the first metre to the ten-thousandth. Standard core bores are 52 mm, 54 mm, 76 mm and 120 mm, matching the mandrels used on most cable taping equipment.

02R-5461 Grade Codes

R-5461-P-GSGlass backed phlogopite mica tape
R-5461-P-GDPhlogopite mica tape with glass on both sides
R-5461-P-GFDPhlogopite mica tape with glass and film
R-5461-P-FSFilm backed phlogopite mica tape
R-5461-S-GSGlass backed synthetic mica tape
R-5461-S-GDSynthetic mica tape with glass on both sides
R-5461-S-GFDSynthetic mica tape with glass and film
R-5461-CM-GSGlass backed calcined mica tape
P = Phlogopite S = Synthetic mica CM = Calcined mica GS = Glass on single side GD = Glass on both sides GFD = Glass and film on each side FS = Film on single side 5461 = Product serial number

03Performance Parameters

Swipe horizontally to see all columns →

Item Unit 0.10 mm 0.12 mm 0.14 mm
Appearance — No alien material, no split, no scar or hole, no broken fold
Length m 500 / 1000 / 2000 (up to 50,000 m in spool)
Thickness mm 0.10 ± 0.015 0.12 ± 0.015 0.14 ± 0.015
Weight of tape g/m² 129 ± 8 161 ± 10 173 ± 12
Mica content g/m² 80 ± 3 110 ± 5 120 ± 5
Binder content g/m² 21 ± 3 23 ± 3 25 ± 5
Breakdown voltage kV >1.2 >1.6 >1.8
Tensile strength N/15mm >120
Fire grades ℃ BS 6387 / 850 ℃–900 ℃, IEC 60331

Test data above refers to type R-5461-CM-GS. Other mica paper and reinforcement combinations are available on request.

04Why It Performs Under Fire

Holds its dielectric strength at high temperature

The R-5461 series does not break down under combined high temperature and voltage within the rated fire period, keeping the circuit alive for emergency lighting, alarms and pumps.

Stable chemistry, long shelf life

Excellent acid and alkali resistance with strong ageing resistance. Stored dry at room temperature, the tape keeps its properties for at least one year.

Clean burn behaviour

No toxic components in the formulation and no toxic gas released at high temperature, which matters in tunnels, ships and enclosed public buildings.

Built for high-speed wrapping

Good tensile strength with high flexibility, so the tape bends around tight cores without cracking and survives the tension of high-speed taping lines.

Consistent surface quality

Smooth, flat and dry to the touch. The tape does not self-adhere on the spool, so it unwinds evenly from the first metre to the last.

Full slitting range

Widths from 4.5 mm to 1000 mm and thicknesses from 0.08 mm to 0.20 mm, wound on 52 mm, 54 mm, 76 mm or 120 mm cores to match your equipment.

05Typical Applications

Oil platforms Multi-storey buildings Power stations Industrial plants Tunnels Computer centres Aerospace centres Telecommunication centres Ships Military installations

Packaging & storage: supplied in cardboard boxes or wooden boxes. Keep in a dry environment at room temperature; storage period is at least 1 year.

06Buyer Questions

How many metres of mica tape fit on one spool?

Up to 50,000 m on a single tray, with a tray diameter of 400 mm and a height of 400 mm. Standard rolls are 500 m, 1,000 m or 2,000 m for buyers who prefer the smaller format.

Which thickness and width combinations are available?

Thickness runs from 0.08 mm to 0.20 mm and slitting width from 4.5 mm to 1000 mm. Standard core bores are 52 mm, 54 mm, 76 mm and 120 mm. Custom widths and core sizes can be produced to your drawing.

Which fire test standards does the tape meet?

The R-5461 series is tested to BS 6387 at 850 ℃–900 ℃ and to IEC 60331, the two standards most commonly written into fire-resistant cable specifications.

Factory direct · Free sample

Need a longer mica tape run?

Send your thickness, width, core size and fire standard. Kaxite will match the R-5461 grade and spool length to your wrapping line.

Send Inquiry
Contact Info
Leave us messages, we'll provide the best solution for you!
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept